There are many kinds of protection methods for automobile wiring harnesses, such as tape wrapping/external casing protection/plastic parts protection. The corrugated bushings have their own corresponding processing equipment as a special protection method for wire harnesses. Today we will look at the commonly used protective sleeves for wire harnesses. The processing method of the tube.
The first is the corrugate tube. Corrugated sleeves come in a variety of materials, such as PA/PE/PP, and even nylon. Most of the materials commonly used in automotive wiring harnesses are PP (polypropylene). The main characteristics are high voltage resistance/corrosion resistance/friction resistance/impedance, and one of the most important features is flame retardant, which is also used in some parts of automotive wiring harnesses. It is an important reason for external protection.
The corrugated casing needs to determine whether it is longitudinally open before entering the factory. If it is intended to be manually cut (hand tool), it is better to choose the opening; if it is intended to be machined, it is better to choose not to open it, because most machines cannot be machined and have been opened longitudinally. The corrugated casing that passes through is very simple. When the blade is pressed down the cutting sleeve, the sleeve that opens the mouth can not withstand the pressure and will collapse, and the processing cannot be continued. As shown below
The wave troughs are mentioned in the figure, which is also necessary to pay attention to during the processing, because the internal wires need to be protected, so the contact point when the blade is cut can only be “peak†(because it is high).
Processing machines are usually divided into two major parts, the casing placement area (curl) + machine work area.
After placing the sleeve, select a series of transfer tubes that match the outer diameter of the sleeve, then insert the sleeve from the machine inlet, pay attention to the limit column at the inlet, and press down to fix it.
Continue to feed the corrugated casing that needs to be processed into the machine. The black cone in the lower part is the cutter area conduit.
After the corrugated bushing is fully inserted, the preparation is ready. Let's take a look at the internal contour of the machine.
There are 4 knobs in the picture that can be adjusted (there is one outside, a total of 5), these 5 are the key parameters of the processing.
Casings of different diameters correspond to different moving parameters, such as knob 1 is to adjust the control pressure gap, 3 is to adjust the blade cutting position, etc.; usually, there is a work instruction in the work area, which shows the common set The parameters corresponding to the pipe processing are easy to understand and operate after the employees are qualified for training.
Here is a special description of the blade area, because this is the core machining part of the machine, this machine is composed of three blades, two of which play the role of positioning, the other is responsible for cutting, similar to a three-point fixed circular structure And there is an infrared sensor above the blade, which is responsible for sensing whether the sleeve is completely in the range of blade processing.
This is a corrugated casing processing equipment imported from abroad. Its function is to cut the corrugated casing longitudinally + transversely cut (peak), and process it into the length we need; in fact, there are many similar suppliers in China. The principle is very simple and can be copied, but the blade processing precision and durable program need to be improved. I hope that more and more Made in China can be seen in the future, and it is competitive to occupy market share!
0.8mm Pin Header
Antenk 0.8mm Pitch Male Header series is a fine pitch, low profile, single/dual/three/four row, PCB mounted connector set intended for limited space applications or where total weight is a factor. Our specially tooled insulators and contacts maintain consistent high quality through our automated production processes. Each series is available in thru-hole PCB or SMT mounting and plated tin, gold or selective gold as specified.
0.8mm Pin Header Options
Number of Rows
1/Single
2/Double
3/Three
4/Quad
Number of Positions
2 Position
3 Position
4 Position
5 Position
6 Position
8 Position
10 Position
12 Position
14 Position
15 Position
16 Position
17 Position
20 Position
Termination Style
SMD/SMT
Through Hole
Mounting Angle
Right Angle
Straight
0.8mm Pin Header Specifications:
Material: Standard Hi-Temp insulator: Nylon 6T, rated UL94V-0
Insulator Color: Black
Contacts: Phosphor Bronze
Plating:
U = Gold over nickel underplate
SG = Gold over nickel underplate on
contact area, tin over copper underplate on tails.
T = Tin over copper underplate overall.
Electrical:
Operating voltage: 250V AC max.
Current rating: 1 Amp max
Contact resistance: 20 mΩ max. initial
Insulation resistance: 5000 MΩ min.
Dielectric withstanding voltage: 1000V AC for 1 minute
Mechanical:
Mating durability: 500 cycles min.
Temperature Ratings: Operating temperature: -40°C to +105°C
Max process temp: 230°C for 30 ~ 60 seconds (260°C for 10 seconds)
Soldering process temperature: 260°C
Packaging:
Anti-ESD plastic bags or tubes
Approvals and Certifications:
UL Recognized File no. E224053
Pin Header,0.8Mm Male Header,0.8Mm Pin Header,0.8Mm Male Header Pins,0.8mm Pitch Pin Header,SMT 0.8mm Pin Header, THT 0.8mm Pin Header
ShenZhen Antenk Electronics Co,Ltd , https://www.pcbsocket.com