Bluetooth Low Energy, referred to as BLE. Bluetooth low energy wireless technology uses many intelligent means to minimize power consumption.
The Bluetooth low energy architecture consists of two chips: a single-mode chip and a dual-mode chip. The Bluetooth single-mode device is a new chip in the Bluetooth specification that only supports Bluetooth low energy technology - part of a technology optimized for ULP operation. The Bluetooth single-mode chip can communicate with other single-mode chips and dual-mode chips. In this case, the latter needs to use the Bluetooth low energy technology part of its own architecture to send and receive data. Dual-mode chips can also communicate with standard Bluetooth technology and other dual-mode chips using traditional Bluetooth architecture.
TI's Bluetooth low energy devices for sensing applications are true SoC solutions. The CC254x SoC Series is a highly flexible, low-cost single-mode Bluetooth low-power solution that combines TI's protocol stack, profile software, and sample applicaTIon. Next, we will combine CC254x to explain the development process of Bluetooth 4.0 from the construction of the environment to the development of the Bluetooth 4.0 protocol stack. This tutorial is divided into six parts. The main points of knowledge are as follows:
The first part of the knowledge points:
The first section of the BLE development environment
The second quarter BLE quick experience
Section III Creating an IAR Project - Lighting LEDs
The fourth section controls the LED
The fifth section LCD12864 display
The second part of the knowledge points:
The sixth section of the independent button query method
Section 7 Interrupt Mode of Independent Buttons
Section VIII CC254x internal temperature sensor temperature acquisition
Section IX five-way button
Section 10 Buzzer
The third part of the knowledge points:
Section XI Serial Communication
Section 12 Flash read and write
Section 13 Introduction to the BLE Protocol Stack
Section 14 How OSAL Works
Section 15 BLE Bluetooth 4.0 Protocol Stack Startup Analysis
The fourth part of the knowledge points:
Section 16 Protocol Stack LED Experiment
Section 17 Protocol Stack LCD Display
Section 18 Protocol Stack UART Experiment
Section 19 Protocol Stack Five-way Button
Section 20 Protocol Stack Flash Data Storage
The fifth part of the knowledge points:
Section 21 DHT11 Temperature and Humidity Sensor
Section 22: Slave Communication of the Bluetooth Protocol Stack
The twenty-third section of the Bluetooth protocol stack master-slave host communication
Section 24 OAD Air Upgrade
Section 25 SBL Serial Port Upgrade
The sixth part of the knowledge points:
Section 26 UBL-USB Upgrade
Section 27 MT-iBeacon Base Station Using iPhone Air Upgrade
Section 28 MT-iBeacon Base Station Implements OAD Air Upgrade on the PC Side
Section 29 MT-iBeacon Base Station About the Use of LightBlue Software
Section 30 How to use the pass-through function of MT-USBDongle
For an introduction to TI's CC254x chip, you can click on the link below to view:
Mainstream Bluetooth BLE control chip detailed (1): TI CC2540
BLE is one of the Bluetooth 4.0 specifications, where the master has up to seven peripherals, low power, low latency, and low throughput.
Six device states
Standby: The device does not transmit and send data, and is not connected to any device.
Broadcast status (Advertiser): Periodic broadcast status
Scanner: Actively looking for devices that are being broadcast
Initiator: Initiator initiates a connection to the scanning device.
Master: Connect to other devices as a master device.
Slave: Connect as a slave to other devices.
Five working states
Standby, advertising, scanning, initiating, connected
Four device types
Cnetral host (often as a client): such as a mobile phone, PC
Peripheral slave (often as a Service): such as a heart rate monitor, blood glucose meter
Observer observer:
Broadcast broadcaster:
Connection process:
Peripheral turns on the broadcast-->Central scan slave broadcast-->Peripheral receives the scan request from Central, and Peripheral sends the scan response data to Central-->Central initiates the connection to Peripheral-->Start communication.
compatibility
Laser Engraving Logo Wood Usb Flash Drive Memoria Usb 4GB 8GB 2.0 3.0
1. Make the logo on usb as the customers design
2. Can preload the file intousb and make the file non-delete
3. The advertisement file can be Auto-play when plug usb into the computer
4. Add more value to your giveaway by adding a Key Chain,Lanyard Neck String or USB Extension Cable
5. Ask us about a wide selection of packaging options,including variety of gift boxes and customized clam shells
6. Making encryption to protect your data
Wooden Usb Flash Disk,Biodegradable Card Usb Flash Dis,Environment-Friendly Card Usb Flash Disk,Flash Disk
MICROBITS TECHNOLOGY LIMITED , https://www.microbitstrade.com